How to cut wood with a table saw

Cutting wood is one of the primary tasks in DIY handyman work. Far from being monotonous and tiring, sawing by hand is a relaxing activity, Very satisfactory, and also allows us to probe the mechanical qualities of the wood that we have chosen. Every amateur in the carpentry industry must have perseverance to learn to handle the saw.

Although it seems contradictory, the hand-cutting saves us time, since electric saws require some preparations that are unnecessary with the saw. And in addition, by hand we will in many cases obtain a more precise cut, and also easier, since we will adjust the passage of the leaf to the variations of a living matter as is the wood.

The two-sided marking with the square allows us to verify that the leaf, besides following the line on the surface, advances completely vertical. It is normal for beginners to make deviations from the perpendicular, and, although the error is minimal, is usually enough to break the joint at an angle. It is preferable to mark and cut again to try to correct a roof profile with the brush or file.

The beginning

To start cutting, we will put the thumb in the end of the line, we will support it in the leaf, and we will move the saw pulling toward us. In that way we open a groove so that the blade penetrates without chaotic sweeps. We will hold the tool firmly but gently, so that the work will do the saw, as the good carpenters say. They also say that there are no tricks to get it right from the beginning: cutting wood is learned by cutting wood.

The saw will work more smoothly and swiftly if the cut is transverse to the grain, although in that way it will cut better. Especially when starting the cut, the blade should have little inclination.

The different types of saws

There are many types of saw, and the basic difference is the number of teeth per inch that has the blade. This will depend on the speed of the cut and the fineness of the finish. A blade with few teeth will cut quickly, in less passes, but both sections will be rough and chipped. A leaf with many teeth will take longer to cut the same wood, but the edges will be smooth and, in some cases, as if they had been sanded.

If you are lazy and just want a table saw that will do all the work for you then read some reviews of the best table saws. Although this article is about using hand saws there are times when it just wont work so it pays to read up on the other types so that you have all the bases covered.

Installing a Countertop, Sink and Kitchen Faucet


The granite counter top gives consumers an elegant and durable work surface for their kitchens that will give them years of service. Traditionally, installing a granite counter top was a job that was left to the pros. Due to the nature of the material, previously highly specialized tools were required to achieve a quality installation .

However, with the increasing popularity of these, they are now available in standard shapes and sizes with preformed edges at a reasonable price, and the kitchen installation techniques have evolved so that any quality contractor can offer this service.

Before you begin installing a granite counter top. Carefully remove material from the existing hob, disconnect all gas lines and remove appliances.

Always have at least one helper when placing heavy boards. Granite can crack or break under its own weight, especially in weak spots like around the sink cutouts.
Make sure all cabinets are level and securely attached to the floor and wall. The top surfaces of the cabinets should be level with a variation of less than ⅛ inch in a 10-foot span. Wall surfaces should be plumb with a variation of less than ⅛ of a straight plane in a 10-foot span. Exceeding these tolerances will result in excessive wedging and wide spaces with filler material.

Although some granite slabs over 20 millimeters thick can be used without the need for a complete substrate that supports the stone, typically at least ¾ inch plywood should be placed at sea or outdoors above Cabinets to support granite.

Drill pilot holes to prevent chipboard material from fraying and secure the plywood with screws. Sinks may require additional framing or supports to support the weight of the sink and its components.

When the granite counter top arrives you will need help putting it in place. Be very careful, as the granite slabs easily break, especially along the natural veins of the material.

Make sure that the plate is level from side to side, and from front to back. Make recess cuts if necessary.

Put in the sink

After the counter is on it’s time to install the sink. This is pretty straight forward so we wont go into it in too much detail.

Put in the kitchen faucet

After you have installed the sink it’s now time to install the kitchen faucet. Assuming you did your research and read top faucet reviews before buying, you should have a product that will fit nicely in your sink. All you should have to do is pop it in and tighten the fasteners so that it doesn’t go anywhere.

Troubleshooting a Garbage Disposal

Well, before you start solving any problem, I want you to promise me that you will obey the cardinal rules of “Repairing a Garbage Disposal”. That is, you will never
put your hand in the hole (down the drain in the disposal)
That said, let’s take a look at repairing this vital piece of kitchen equipment so that it can become one of the best garbage disposals you’ve ever had.

garbage disposalThe disposal does not turn on (no noise)
If the crusher does not turn on and is not humming, then there is an electrical problem.

This may seem obvious, but make sure the crusher is plugged in.
If connected, press the Reset button on the bottom of the unit. If it has been reset, the button will skip.
If that does not work, check if the circuit breaker has tripped and turned off at the electrical service panel.
If the switch has not tripped and the reset button is not popped out, then it is a faulty switch or a defective trash crusher. First locate the switch that powers the disposal unit. It should be located on the wall, but may be under the sink.
Turn off the switch on the service panel that feeds the shredder.
Replace switch.
Turn it back on at the service panel and check if the crusher is working.
If the crusher does not work and does not make noise, the trash crusher is beyond repair and needs to be replaced.

Sask Campus

Welcome to Sask Campus. This is our news site based out of Saskatchewan Canada that covers a wide range of topics. Check back regularly for awesome content from guest readers all over the world.